TDMK series motor rated voltage is 6000V but also the voltage can be as customer requires such as 3000V,10000V.The allowed voltage warp is ±5%.rated frequency is 50hz,rated power factor is 0.9(leading).
Parameter of TDMK large three-phase synchronous motor:
l Cooling method : IC01,IC27,IC37,IC81W,IC91W.
l Protection lever: IP00,IP20,IP21,IP23 and IP44.
l Rated voltage :6000v
l Frequency:50hz
Application of TDMK large three-phase synchronous motor:
TDMK series motor is mainly used for driving the mine mill, crusher,for example: grate mill, rod mill, coal mill etc,.
Rated voltage: 3000V; 6000V; 10000V
Rated:50Hz
Power scope: 280~2000kw
Speed:250rpm; 200rpm; 187.5rpm; 167rpm; 150rpm;100rpm
Mounting type:horizontal type
Cooling Method:open self-ventilation、or duct or half duct ventilation as customer’s need
Insulation grade:B /F
Altitude:below 1000M
Temperature:not exceed 40℃
Environment requirement:few dust, no steam, no acid, no alkali in the air.
Motor introduction
TDMK series motor ‘s rotation direction can be clockwise also anti-clockwise seeing from the slip ring side.
When the motor is coupling the milling machine, the DE end of the motor can not suffer the axial force or radial force in addition.
TDMK series motor starting method is full voltage starting. If the power is not enough, the motor can be started with reduced voltage properly. The starting current and the starting torque will be lower as well.
Stator out cables: 6 lines(U1、V1、W1、U2、V2、W2)
Sat sleeve bearing: oil ring bearing or multiplex bearing. There is a rubber pads between bearing and the motor frame to avoid the shaft current.
Structure:
Frame: integral construction welded by steel plate
Stator: laminated by 0.5mm silicon steel fan shaped lamination. The insulation class can be B or F.
型号 | 额定 功率 KW |
额定 电压 KV |
额定 电流 A |
额定 转速 r/min |
功率 因数 (超前) |
堵转 转矩 额定 电流 |
牵入 转矩 额定 转矩 |
先步 转矩 额定 转矩 |
重量 t |
备注 |
TDMK350-32 | 350 | 6 | 41 | 187.5 | 0.9 | 6.72 | 1.1 | 3.56 | 10.7 | |
TDMK400-32 | 400 | 6 | 47 | 187.5 | 0.9 | 6.54 | 1.132 | 4.06 | 11.3 | 轴打孔 |
TDMK400-32 | 400 | 10 | 28 | 187.5 | 0.9 | 6.67 | 1.09 | 3.21 | 12.2 | |
TDMK500-32 | 500 | 10 | 35 | 187.5 | 0.9 | 6.24 | 1.03 | 3.5 | 13.7 | |
TDMK500-36 | 500 | 6 | 58 | 167 | 0.9 | 6.27 | 1.04 | 3.0 | 12.7 | |
TDMK630-36 | 630 | 6 | 74 | 167 | 0.9 | 6.13 | 1.02 | 2.9 | 13.5 | |
TDMK800-36 | 800 | 6 | 93 | 167 | 0.9 | 5.9 | 1.0 | 2.7 | 16.0 | |
TDMK800-36 | 800 | 10 | 55.8 | 167 | 0.9 | 6.67 | 1.08 | 3.47 | 16.8 | |
TDMK1000-36 | 1000 | 6 | 115 | 167 | 0.9 | 6.1 | 1.0 | 3.0 | 16.0 | |
TDMK1000-36 | 1000 | 10 | 69 | 167 | 0.9 | 5.0 | 1.0 | 2.6 | 17.7 | |
TDMK1600-36 | 1600 | 6 | 181 | 167 | 0.9 | 6.7 | 1.19 | 2.98 | 31.0 | |
TDMK1250-40 | 1250 | 6 | 143 | 150 | 0.9 | 6.17 | 1.0 | 3.36 | 17.7 |